Firmware Files

Select a firmware category from the list below to see all the downloadable files and their descriptions in that category. Go to Archived Firmware Files to find previous versions of firmware.

Modero X Series G5 Touch Panels Firmware
Prerequisites: None

-------------------------------------------------------------------------------
Changes in This Release
-------------------------------------------------------------------------------

    * Add IPv6 Support. 
      - IPv6 support is disabled by default.
      - Supports Link-local IPv6 address, neighbour discovery IPv6 address, 
        and static IPv6 address. 
      - IPv6 gateway can be discovered using IPv6 router discovery or a static
        IPv6 gateway can be set.
      - Static IPv6 settings that can be set are the IPv6 address, the IPv6 
        subnet prefix length, the IPv6 gateway, and the IPv6 DNS servers.
    * Add secure master connection. 
      - Secure connection uses TLS with x.509 certificate connection 
        verification. If the master uses a custom device certificate, then that 
        certificate should be installed in the panel using:
        Settings->Security->Credential Storage->Install From Storage->Trusted CA
    * Added 802.1x support. 
      - Supplicant uses FIPS 140-2 library for 802.1x which limits 
        EAP method/Phase 2 authentication to only TTLS/PAP. Certificate used for
        IPv6 must be installed using:
        Settings->Security->Credential Storage->Install From Storage->802.1x
    * Added support for IPv6 addresses being used with dynamic images.
      - ^RAF/^RMF commands now support IPv6 addresses HTTP. IPv6 addresses 
        should be inside [] (e.g. [2001::1] )
    * Added password protected button property.
    * Add G5 support for HTTPS client options.
      - Validate HTTPS Server Certificate: If enabled, the HTTPS server 
        certificate is validated while the connection is being negotiated.
      - Verify HTTPS Server Hostname: If enabled, verify the HTTPS server 
        hostname matches the HTTPS server certificate.
    * Add modal popup support and support for popups with names  ( _name ).
      - Enforce modal popups and popups with names beginning with underscore
        are highest in Z order of popups in the order of attachment.
    * Added FIPS 140-2 SSL/TLS approved library to platform.
    * Add support for Audit Logging to a NetLinx master which will log
      to the syslog server if configured.
    * Add central storage for encrypted data. Usernames/passwords from previous
      versions will be migrated but if downgrading to prior release then
      the current usernames/passwords will not be downgraded to previous 
      version. They should be reset on downgrading of firmware versions.
    * Added USB security settings.
    * Add support for enclosing ListView .csv fields inside quotations.
      - Support escaping quotation marks inside of quotes with consecutive 
        quotation marks.
    * Add Firefox as default browser.
    * Add 'scale - maintain aspect ratio' image justification. 
      Justification value is 11 when using a SEND_COMMAND to set the 
      justification for a image.
    * Add support for custom NTP server. Panel time is set to master time by 
      default.
    * Add clear icon to ListView search field.
    * Add support for ^BML command and %ML ^BMF option.
    * Added Custom Event when USB is plugged/unplugged.
        custom.id   = 0
        custom.type = 791
        custom.flag = 1 if USB device was attached. 0 if USB device was detached.
        custom.value1 = 0
        custom.value2 = 0
        custom.value3 = 0
        custom.text   = 'USB device attached' or 'USB device detached'
    * Add ^SAD Subpage Add command. Adds a subpage to a set but doesn't change 
      the set anchor.
    * Fix Intercom/SIP commands not always reported in right port.
    * Fix level types not being retained after an online/offline.
    * Fix level types not being reported correctly in some cases. This could 
      cause a level that is signed and went negative to be displayed at max 
      positive values.
    * Fix where after a TPD5 file transfer the panel came online two times.
    * Fix text append to a Text Input button.
    * Fix ^BAT command to accept ISO-8859-1 encoded text instead of UTF8 encoded
      text.
    * Add ^BAF command that expects UTF8 encoded text.
    * Fix ListView refresh commands from updating UI until list data has been 
      processed.
    * Fix problems with ^BMF subcommand %GV, removed subcommand %SH and fixed 
      issue with ^UTF command not showing Unicode characters.
    * Fixed issue with ^TPN where page tracking would not occur after startup 
      (when enabled) until ^TPN was sent to the touch panel. Pages will now be 
      tracked upon startup if page tracking is turned on.
    * Fixed single line text buttons so that a done button always appears 
      instead of a return button.
    * Fixed single line text buttons so that done button sends contained string 
      to master.
    * Fixed text buttons so that when cancelled only one abort message is sent 
      to the master. Cancelling is done by either changing focus to different 
      buttons or closing the keyboard.
    * Fixed multiline text buttons so that a done button is shown with the 
      keyboard.
    * Fixed bug with password dialog where enter key on hardware keyboard would 
      add new line. Hardware keyboard's enter keys now act as pressing OK on the
      dialog. Pressing 'Done' key on soft keyboard now is the same as pressing 
      OK on the dialog.
    * Fix ListView to handle using SQL keywords in column/table names.
    * Fix video streaming using UDP/RTP data on a multicast IPv6 address.
    * Fixed ^BMF %P and %SO options not able to be cleared.
    * Fix HTTP Digest authentication for MD5-sess algorithm.
    * Fix HTTP Digest authentication when server sends HTTP redirects.
    * Fix VNC input location offset errors.
      - Errors introduced through new display timings in 19" and 20" panels 
        requiring display buffer size changes that were not compensated for in 
        the VNC server input.
    * Fix where multiple subpage viewers with the same address code didn't 
      handle subpage show/hide send commands correctly.
    * Fix subpages intermittently not anchoring in correct position after 
      multiple ^SSH/^SHD commands.
    * Fix crash when multiple subpages were hidden/shown simultaneously.
    * Increase the dispatching timeout to 20 seconds from the default 5 seconds
      to reduce ANR messages.
    * Ensure inactivity page flip tracking sent to master.
    * Only send ^WCN response if VNC is enabled.
    * Fix PKEYB and PKEYP commands not displaying keyboard/keypad if no '-' is 
      part of the command.
      - Add support for @PKB command. Syntax same as ^PKB.
    * Allow dynamic images loader to continue to attempt connections after 3 
      failed attempts, but do so at a reduced rate.
    * Handle encoded paths and files in ^RMF/^RAF commands.
       - Fix Resource path (%A) and File (%F) parameters that contain URL 
         encoded text (%%xx).
    * Fix HTTP get of dynamic image when no content-type is in the 
      server response.
    * Fix mishandling of URIs like http://user@server:pass@host:port/path/file.
      (Usernames that have an '@'.)  
    * Handle URL encoding/decoding in Dynamic Images and ListView Images.
   

ZIP | 245 MB | v. 1.7.30 | 2017-12-04
MXD-1001
MXD-1901-PAN
MXD-2001-PAN
MXD-701
MXR-1001
MXT-1001
MXT-1901-PAN
MXT-2001-PAN
MXT-701
Modero X Series G4 Touch Panels Firmware
--------------------------------------------------------------------------
Prerequisites: 
--------------------------------------------------------------------------
TPDesign4 3.3.0 build 672 or later, with G4 Support Files version 3.3.44 or 
later.
Intercom module v1.9 or later (if using with Intercom).
SIP module 2.11 or later (if using with SIP).
MXA-MPL 2.1.112 (if using with Multi Preview Live).

--------------------------------------------------------------------------
Changes in This Release
--------------------------------------------------------------------------
-- Added support for an updated LCD controller revision for the 19" and 20" Modero-X 
   (MXT-2000XL-PAN, MXD-2000XL-PAN, MXT-1900L-PAN, MXD-1900L-PAN) 
-- RFI-30527: Added retry delay when attempting to reopen a TCP socket to 
   handle socket close-reopen race condition when ^RMF is issued to change
   resource.
-- RFI-30611 support for ^STS command to disable/enable subpage touch scrolling
-- RFI-30712 support for ^SRO command to reset subpage ordering within a viewer
 
--------------------------------------------------------------------------
Addressed Common Vulnerabilities and Exposures List
--------------------------------------------------------------------------
- CVE-2012-0920, CVE-2013-4421, CVE-2013-4434, CVE-2015-7547 CVE-2016-7406, 
- CVE-2016-7407, CVE-2016-7408, CVE-2016-7409

--------------------------------------------------------------------------
Known Issues
--------------------------------------------------------------------------
- Available in the readme file
--------------------------------------------------------------------------
Programming Information
--------------------------------------------------------------------------
- New or Modified Send Commands are available in the readme file and the Configuration and Programming Guide
--------------------------------------------------------------------------
 

ZIP | 48.34 MB | v. 2.104.134 | 2017-05-25
MXD-1000
MXD-1000-NC
MXD-1900L-PAN
MXD-1900L-PAN-NC
MXD-2000XL-PAN
MXD-2000XL-PAN-NC
MXD-430
MXD-700
MXD-700-NC
MXT-1000
MXT-1000-NC
MXT-1900L-PAN
MXT-1900L-PAN-NC
MXT-2000XL-PAN
MXT-2000XL-PAN-NC
MXT-700
MXT-700-NC
Modero S Series Touch Panels Firmware

Prerequisites:

  • TPDesign4 v3.3 build 674 or later, with G4 Support Files version 3.3.58 or later
  • Intercom module v1.9 or later (if using with Intercom)
  • SIP module 2.11 or later (if using with SIP)

Changes in This Release:

  • Fix for hostname persistence when using static IP configurations on an MST-431 and MSD-431.
  • Added User-Agent field in HTTP headers for dynamic image downloads to support servers that require it.
  • Migrated to Dropbear SSH 2016.74 to address the following related vulnerabilities; CVE-2016-7406 CVE-2016-7407 CVE-2016-7408 CVE-2016-7409.
  • Added fix for the Ping Command security issue.
  • Decreased the time for the Subpage scrolling to stop at its anchor
  • Fixed issue where the panel would either lockup or reboot due a memory leak and poor graphics memory management.
  • Fixed issue where the panel would reboot when the Computer Control window is set to scaled to fit.

Addressed common Vulnerabilities and exposures list:

  • CVE-2012-0920, CVE-2013-4421, CVE-2013-4434, CVE-2015-7547 CVE-2016-7406
  • CVE-2016-7407, CVE-2016-7408, CVE-2016-7409

Known Issues
ETHERNET:

  • It is possible on some panels for the device's MAC address to get lost or corrupted. If this happens, the device will automatically generate a random MAC address. This address is not guaranteed to a Globally Unique Identifier(GUI), but it will not conflict with any non-AMX devices. If the device is having connectivity issues, it is recommended that the "check eeprom" command be run from a telnet session. This command will check the MAC address, and give the user the option to fix it.

VIDEO:

  • The following streaming video modes are supported for the 7" Modero S Touch Panels: MPEG2 video and MP2/MP3 audio over MPEG2 Transport Streams (from MAX-CSE or Vision2 Server), H.264 video and AAC audio over MPEG2 Transport Streams (from MXA-MPL or Vision2 Server), and Motion JPEG over HTTP. 3rd Party MPEG2 and H.264 encoders have not been tested, are not supported by AMX, and may or may not work. Please see the Modero S Programming Guide for more detailed recommendations on video configuration.
  • The following streaming video modes are supported for the 4.3" Modero S Touch Panels: Motion JPEG over HTTP
  • Streaming Video/audio performance can depend on multiple factors, like: downscaling ratio, network bandwidth, network congestion, other simultaneous panel activities, stream characteristics (bit rate, encoding method), etc. There is no buffering on the panel for video streams (though there is a small latency), so any anomaly in the network can result in a visible (or audible) glitch. To help improve performance in challenging environments, consider reducing the resolution of the content (480p is recommended), reducing the bit rate of the stream, reducing the downscaling ratio, and preserving the aspect ratio.
  • For any type of streaming video, there could be a 1-3 second latency. For Motion JPEG, this latency can be improved by using smaller (i.e. < 800x480) video buttons and/or reducing the frame rate of the server.

RECOVERY:

  • It may take several presses to get the touch to register if attempting to use the "Dots During Boot" firmware rollback method. Firmware rollback is also available from the Setup Pages menu if needed.


ZIP | 48.52 MB | v. 2.108.40 | 2017-03-28
HPX-MSP-10
HPX-MSP-7
MSD-1001
MSD-431
MSD-701
MST-1001
MST-431
MST-701
Modero MVP-9000i Touch Panel Firmware

Order updated FCC label - no charge

Changes in this release:

  • Fixed issue with the flyout buttons on the left side of the front panel. The panel will appear to stall and possibly revert to the main startup page if any of the four flyout buttons are pressed after a bootup but before the capacitive touch pad on the right side of the front panel is pressed.
  • Fixed a SIP registration issue where registration with some SIP proxies would fail if the proxy was unable to accept an "expires" value of 180 seconds. An "expires" value of 3600 is now the default.
  • Fixed a SIP issue where cycling the SIP state between enabled and disabled could sometimes cause the panel to get stuck in a state where it could no longer register with the proxy until the panel was rebooted.
  • Fixed issue where user was unabled to enter setup pages by holding their finger on the screen during boot.
  • Fixed issue with a channel assigned to the cradle sensor getting out of sync after a reboot.
  • Fixed issue where motion jpeg images would not display if the server rejected HTTP/1.0 requests.
  • Fixed issue where the dock sound would play any time the panel became disconnected from the master.
  • Updated WiFi firmware to conform to R&TTE adaptivity requirements described in the ETSI R&TTE EN 300 328 v1.8.1 standard.

PROGRAMMING INFORMATION:

After upgrading you MUST resave wireless settings. You do not have to reenter the settings. Open wireless page and press save.

Band Selection: Note - The band selection will effect what you see when doing a site survey.

802.11a/b/g -> A and B bands, all channels
802.11b/g -> B band, channels 1,6,11
802.11a -> A band, all channels

Active roaming:
Disabled -> Roaming is passive, and will only occur when the panel loses connection to its current access point Enabled -> The panel is actively looking for better access points to roam to.


ZIP | 31.19 MB | v. 2.86.86 | 2015-06-19
MVP-9000i
Modero MVP-5150/MVP-5200i Touch Panel Firmware

Prerequisites: The panel must be installed with v2.66.21 or greater before upgrading

Changes in This Release:

  • Added support for the detroit screen replacement
  • Added international fonts and gesture support
  • Minor bug fixes

Hot Fix for the Modero MVP-5150/MVP-5200i Touch Panel Firmware (v.2.87.35 Available from AMX Technical Support)

Changes in this release:

  • Fixed the scenario where the graphics would not update on the display
  • Fixed the scenario where the panel drops offline to the AMX master and does not recover the connection

ZIP | 107.16 MB | v. 2.87.13 | 2012-01-30
MVP-5150
MVP-5200i
Modero MVP-5100 Touch Panel Firmware

Prerequisites: v2.66.21 or later must be installed

Changes in this release:

  • Resolved a memory leak issue that could potentially affect the responsiveness of the touch panel, and in some extreme cases cause the touch panel to become unresponsive.


ZIP | 84.97 MB | v. 2.86.5 | 2011-11-14
MVP-5100
Modero MVP-8400 and MVP-8400i Touch Panel Firmware

Changes in this release
Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards.

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.

Setup Pages:

  • Added new calibration page compatible with the new touch calibration.

Hot Fix for the Modero MVP-8400 and MVP-8400i Touch Panel Firmware (v.2.86.71 Available from AMX Technical Support)

Prerequisites:
None.

Changes in this release:

  • Wireless signal level updates on user pages
  • Fixed RMF command to support more than 150 characters

ZIP | 11.02 MB | v. 2.86.55 | 2010-12-01
MVP-8400
MVP-8400i
Modero MVP-7500 Touch Panel Firmware

Important: Panels with more than 1Gb Compact Flash cards should not be downgraded to any version below 2.86.39. This information can be retrieved via Setup pages (Information - File System), or using telnet - (disk free).

Prerequisites: None.

Changes in this release:

Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards.

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.

Setup Pages:

  • Added new calibration page compatible with the new touch calibration.


ZIP | 10.82 MB | v. 2.86.41 | 2010-11-10
MVP-7500
Modero NXD-430 and NXD-435 Touch Panel Firmware

Prerequisites: v2.4.9 or later must be installed before upgrading

Changes in This Release:

  • Resolved a memory leak issue that could potentially affect the responsiveness of the touch panel, and in some extreme cases cause the touch panel to become unresponsive.

Hot Fix for the Modero NXD-430 and NXD-435 Touch Panel Firmware (v.2.86.15 Available from AMX Technical Support)

Changes in this release:

  • Fixed the scenario where the graphics would not update on the display
  • Fixed the scenario where the panel drops offline to the AMX master and does not recover the connection

ZIP | 85.92 MB | v. 2.86.6 | 2011-11-14
NXD-430
NXD-435
Modero NXD-500 Touch Panel with Intercom Firmware

Prerequisites: v2.4.28 or later must be installed before upgrading.

Changes in this release:

  • Resolved a memory leak issue that could potentially affect the responsiveness of the touch panel, and in some extreme cases cause the touch panel to become unresponsive.

Hot Fix for the Modero 5" Intercom Touch Panel Firmware (v.2.86.23 Available from AMX Technical Support)

Changes in this release:

  • Fixed the scenario where the graphics would not update on the display
  • Fixed the scenario where the panel drops offline to the AMX master and does not recover the connection

ZIP | 67.89 MB | v. 2.86.5 | 2011-11-14
NXD-500i
NXD-500iW
Modero NXD-CV5 Touch Panel Firmware

NOTE: Use of the new Connection Utility feature on the setup pages requires master firmware Build 352 or greater.

New Features:

  • Increased IR receiver range
  • Eliminated pixel noise in video windows


KIT | 8.78 MB | v. 2.60.27 | 2008-02-25
NXD-CV5
Modero NXD-700i / NXT-CA7 Touch Panel Firmware

Changes in this release:
Updates to the NXD-700i to flash the LEDs on startup. Updates to the firmware to disable the SIP button in the Setup Pages for the NXT-CA7.

Notes:
The changes for the flashing of the LEDs on startup will also cause the LEDs to flash when new panel pages are loaded to the unit.

Hot Fix For Modero NXD-700i / NXT-CA7 (v.2.92.17 Available from AMX Technical Support):

  • Fixed the scenario where the graphics would not update on the display
  • Fixed the scenario where the panel drops offline to the AMX master and does not recover the connection

ZIP | 23.02 MB | v. 2.92.5 | 2011-11-08
NXD-700i
NXT-CA7
Modero 7" Vi Series Touch Panels Firmware

Important: Panels with more than 1Gb Compact Flash cards should not be downgraded to any version below 2.86.26. This information can be retrieved via Setup pages (Information - File System), or using telnet - (disk free).

Prerequisites: None.

Changes in this release

Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.

Setup Pages:

  • Added new calibration page compatible with the new touch calibration.


ZIP | 11.09 MB | v. 2.86.29 | 2010-11-05
NXD-700Vi
Modero NXD-CV7 / NXT-CV7 Touch Panel Firmware

Changes in this release

Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards.

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.

Setup Pages:

  • Added new calibration page compatible with the new touch calibration.

Hot Fix for the Modero 7" Touch Panels Firmware (v.2.86.40 Available from AMX Technical Support)

Changes in this release:

  • Fixed an issue where the panel could fall off line or reboot due to an issue with the watchdog monitoring system
  • Fixed an issue where the Ethernet driver could crash in high traffic environments


ZIP | 10.89 MB | v. 2.86.29 | 2010-12-02
NXD-CV7
NXT-CV7
Modero 10" Vi Series Touch Panels Firmware

Important: Panels with more than 1Gb Compact Flash cards should not be downgraded to any version below 2.86.26. This information can be retrieved via Setup pages (Information - File System), or using telnet - (disk free).

Prerequisites: None.

Changes in this release:

Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration

Setup Pages:

  • Added new calibration page compatible with the new touch calibration


ZIP | 11.09 MB | v. 2.86.29 | 2010-11-04
NXD-1000Vi
Modero NXD-CV10 / NXT-CV10 Touch Panel Firmware

Important: Panels with more than 1Gb Compact Flash cards should not be downgraded to any version below 2.86.26. This information can be retrieved via Setup pages (Information - File System), or using telnet - (disk free).

Prerequisites: None.

Changes in this release:

Boot:

  • Added support for large (2 GB or greater) Compact Flash Cards.

User Interface:

  • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.

Setup Pages:

  • Added new calibration page compatible with the new touch calibration.

Hot Fix for the Modero 10" CV Touch Panels Firmware (v.2.86.41 Available from AMX Technical Support)

Prerequisites:
None.

Changes in this release:

  • Fixed an issue where the panel could repeatedly fall off line or reboot due to an issue with the watchdog monitoring system. The watchdog is fixed and updated with a logging feature that will persist over reboots for future analysis.
  • Fixed an issue where the Ethernet driver could crash in high traffic environments
  • Fixed issue with bar graphs set using the ^GLH & ^GLL send commands and the handling of negative values.


ZIP | 10.89 MB | v. 2.86.29 | 2010-11-04
NXD-CV10
NXT-CV10
Modero VG Series Touch Panels Firmware

Prerequisites:
None

Firmware Revision History

  • Boot:
    • Delay added to boot to meet spec for large compact flash cards.
  • User Interface:
    • New touch calibration algorithm which provides more accuracy and corrects for nonlinear error in the touch overlays. The new algorithm adds more points to the touch calibration.
  • Setup Pages:
    • Added new calibration page compatible with the new touch calibration.


ZIP | 11.95 MB | v. 2.86.23 | 2010-09-23
NXD-1200V
NXD-1200VG RGB Kit
NXD-1200VG Video Kit
NXD-1500VG RGB Kit
NXD-1500VG Video Kit
NXD-1700VG RGB Kit
NXD-1700VG Video Kit
NXT-1200V
NXT-1200VG RGB Kit
NXT-1200VG Video Kit
NXT-1500VG RGB Kit
NXT-1500VG Video Kit
NXT-1700VG RGB Kit
NXT-1700VG Video Kit
Modero CA/CV-12/15/17 Touch Panels Firmware

KIT | 6.61 MB | v. 2.57.80 | 2005-08-08
NXD-CA12
NXD-CA15
NXD-CV12
NXD-CV15
NXD-CV17
NXT-CA12
NXT-CA15
NXT-CV12
NXT-CV15
NXT-CV17
NXV-300 Modero Virtual Touch Panel Firmware

Changes in this Release:

  • Added schedulable weekly maintenance reboot feature. Once the day and hour are set, the reboot will occur on the 1st minute of the day and hour that was set. The default schedule is Monday 1:01 a.m. To change the schedule, telnet to the NXV-300 and at the prompt type; weekly reset <day> <hour> ;
    where <day> is 1-7. 1 is Mon, 2 is Tues, 7 is Sun, etc.
    <hour> is 0-23. 0 is Mid, 1 is 1am, 13 is 1pm, etc.
    To disable weekly maintenance reboot type; disable reset.
    To enable weekly maintenance reboot type; enable reset.
    To retrieve the weekly reset information type; get reset.
  • As part of routine security enhancements, further security measures added to resolve minor vulnerabilities

Known Issues:

  • In page tracking mode, when the "Sleep" button (with "0-loop back port") of the NXV-300 is clicked using the USB mouse, the NXV-300 may switch between sleep mode and wake mode. This feature also appears to cause other panels connected to the same master to permanently go to into sleep mode.
  • The master settings are still applied even though the "Cancel" button in "System Settings" page was pressed.
  • It is observed that either doing a "Reset System Settings" in the "Protected Setup" page or downloading the full kit to the NVX-300 in 480x272 resolution, the NVX-300 boots up with 800x480 resolution.
  • The text "Bonjour" is missing in the "Device Name" alpha numeric keyboard in the Title position.
  • The display timeout feature is not available.
  • The "Connect Count" in the "G4 Web Control Settings" page is not reliable.
  • The Protected Setup page "Password" is not case sensitive when it is entered using Desktop "Keyboard".
  • The Connection Status Symbol shows up in red color when the NXV-300 connects in URL(UDP) or NDP(UDP) while in DHCP mode, even though Netlinx Studio shows that it is connected to the master.

ZIP | 6.62 MB | v. 2.1.26 | 2016-06-17
NXV-300
Control Phone Interface

Initial release of product


KIT | 8.49 MB | v. 1.0.10 | 2011-06-30
NXV-CPI
MVP Docking Stations v3.00 Firmware

NOTE: This version of firmware is functionally the same as version 2.05. It has been recompiled for new hardware, and changed to version 3.00

NOTES: MVP-WDS and MVP-TDS Firmware. In order to download this or any other cradle firmware, the following panel firmware versions !!MUST!! be present:

  • MVP-8400 firmware higher than v2.84.41
  • MVP-7500 firmware higher than v2.84.31

If the panel firmware does not adhere to the above requirements the cradle will be rendered inoperable by the download and will need to be shipped back to AMX for reprogramming

Fixes:

  • Recompiled for updated processor on new hardware

ZIP | 10 KB | v. 3.00 | 2008-11-17
MVP-TDS
MVP-WDS
Feedback | Gear Store | Site Map | Terms of Use | Privacy Policy | Warranty