NMX-DEC-N2243

JPEG 2000 1080p HD Low Latency Video over IP Decoder with KVM

DescriptionJPEG 2000 1080p HD Low Latency Video over IP Decoder with KVM
Part #FGN2243-SA
This Product Has Been Replaced By: NMX-DEC-N2235

OVERVIEW
The NMX-ENC-N2143 HD Encoder converts video, audio, and control to IP packets for low-latency seamless switching and distribution over standard networks. The NMX-DEC-N2243 HD Decoder accepts the HD over IP streams and converts back to synchronized audio and video to allow any video source to any display. Both models feature keyboard and mouse extension over IP, input and output scaling, embedded 7.1 audio, de-embedded balanced analog audio, and power over Ethernet and comes in stand-alone format.

SPECIFICATIONS

Video
Signal Types
Input
Network video over Ethernet via RJ45
Output
HDMI, DVI-D
Formats
DVI, HDMI (through adapter), HDCP content protection support
Input Resolutions
HDMI and DVI (Progressive)
Matched to inputs or scaled to 720x480@59.94Hz (480p59.94), 1280x720@50Hz (720p50), 1280x720@59.94Hz (720p59.94), 1280x720@60Hz (720p60), 1280x800@60Hz, 1920x1080@50Hz (1080p50), 1920x1080@59.94Hz (1080p59.94), 1920x1080@60Hz (1080p60)
Audio
Signal Types
Input
Network video over Ethernet via RJ45
Output
Embedded audio on DVI-D or HDMI (through adapter)
Formats
HDMI
8ch PCM
Analog
Stereo 2-channel
Digital-To-Analog Conversion
16-bit 32 kHz, 44.1 kHz and 48 kHz
Latency
720p
25 ms
1080p
25 ms

Note: Scaling can add up to 16 ms of latency.

Note: To calculate an end-to-end latency value, add the given Decoder latency (shown above) to your Encoder's latency (which is provided in the Encoder's Specifications sheet).

Communications
Ethernet
10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
USB
Supports keyboard and mouse extension of USB HID 2.0 or 1.0 class devices
HDMI
HDCP, EDID management
Connectors
PWR 12VDC @ 2.0A
One 12 Volt DC power input
P0 POE
8-wire RJ45 female.
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port. Provides both the network connection and the power to the Encoders and Decoders. See the section Power Requirements.
P1
8-wire RJ45 female.
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port.
IR
2-pin terminal Phoenix connector. Provides Infrared (IR) output only (33-60 kHz). Emitter may be necessary (not included).
RS232
3-pin terminal Phoenix connector which provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate.
AUDIO
5-pin terminal Phoenix connector which provides user-selectable balanced/unbalanced input. Dedicated audio output.
DVI-D OUTPUT
DVI-D female; HDMI/DVI digital video/audio output. Allows for video and embedded digital audio output.
KEYBOARD
USB (Standard-A) keyboard connection.
MOUSE
USB (Standard-A) mouse connection.
LEDs and Buttons
FRONT PANEL


RESET button
Recessed pushbutton. Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings.
ID button
Recessed pushbutton. Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command).
POWER LED
On solid (green) when operating power is supplied (via local power supply). This activity is also shown by the PWR LED on the rear panel.
STATUS LED
On flashing (green) when there is software activity. This activity is also shown by the STAT LED on the rear panel.
REAR PANEL


PWR LED
Same as POWER LED described above.
DVI LED
On (green) when a DVI outputconnection exists.
STAT LED
Same as STATUS LED described above.
STRM LED
On (green) when the unit is streaming video.
POWER LED
On (green) when the KVM (keyboard, video, mouse) board is powered.
ACTIVITY LED
On (green) when there is keyboard or mouse activity.
Power Requirements
Power Supply
2.0 Amp @ 12 Volts DC; 100-240 Volts AC power supply; part number NMX-ACC-N9312.
Power over Ethernet (PoE)
Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1).

Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only. PoE does not pass through the daisy chain (P1) port.

Physical
Mounting Options
Stand alone, surface mount, or wall mount. Mounting wings (sold separately — part number NMX-ACC-N9101) are required for mounting.
Environmental
Temperature
32° to 104°F (0° to 40°C)
Humidity
10% to 90% RH (non-condensing)
Heat Dissipation
Up to ~44 BTU/Hr
Dimensions
Height
1.7 inches (4.32 cm)
Width
7.888 inches (20.04 cm)
Depth
5 inches (12.7 cm)
Weight
1.75 lbs (0.79 kg)
Compliance
FCC, CE, and NTRL

*Mounting wings (part number NMX-ACC-N9101) required for surface and wall mounting. Rack shelf (part number NMX-ACC-N9102) or card cage (part number NMX-ACC-N9206) required for rack mounting. Shelf accommodates two side-by-side N-Series encoders and decoders. Card cage accommodates up to six N-Series encoder and decoder cards (mix and match any series). Mounting accessories sold separately and are compatible with most N-Series devices.



Note: Specifications are subject to change. The most current and complete specifications for this product can always be found at AMX.com: AV for an IT World.


NAME DESCRIPTION PART #
NMX-ACC-N9101 N-Series, Mounting Brackets (FGN9101)
NMX-ACC-N9102 Rack Shelf, 1RU, 2 N-Series Units (FGN9102)
Feedback | Gear Store | Site Map | Terms of Use | Privacy Policy | Warranty