NMX-DEC-N2241

JPEG 2000 1080p HD Low Latency Video over IP Decoder

DescriptionJPEG 2000 1080p HD Low Latency Video over IP Decoder
Part #FGN2241-SA
This Product Has Been Replaced By: NMX-DEC-N2235

OVERVIEW
The NMX-ENC-N2141/NMX-DEC-N2241 AV over IP Series provides a flexible, feature-rich, and simple-to-deploy Digital Media Distribution and Switching solution satisfying the most demanding applications. The NMX-ENC-N2141/NMX-DEC-N2241 provides low latency for 1080p/60hz encoding and decoding. SVSI video over IP encoders are used to encode and distribute sources of almost any format onto an existing IP network making that stream available to any endpoint in the facility. Video over IP Decoders are used to decode SVSI's Networked AV streams back to DVi or HDMI format for display on any monitor. With the ability to direct any source stream to any display, large, low-cost switching and distribution systems are simple to deploy without proprietary cabling or dedicated switching hardware.

FEATURES

  • 1080p/60hz encoding and decoding.
  • Input and Output Scaling – scaling performed in encoders or decoders for maximum flexibility with V-Series sources and displays
  • Power Over Ethernet (POE) – eliminates requirement for local power supply and speeds installation. Units can still be powered locally from 12VDC allowing for easy rack-mountable, high-density installations
  • Infrared (IR) emitter connection allows control of low-cost, IR-only display devices
  • Fast install with Phoenix connectors for Power, IR, RS232 serial, and analog audio interfaces
  • Pass-through DVI interface allows easy installation with local display such as desktop PC applications

SPECIFICATIONS

Video
Signal Types
Input
Network video over Ethernet via RJ45
Output
HDMI, DVI-D
Formats
DVI, HDMI (through adapter), HDCP content protection support
Input Resolutions
HDMI and DVI (Progressive)
Matched to inputs or scaled to 720x480@59.94Hz (480p59.94), 1280x720@50Hz (720p50), 1280x720@59.94Hz (720p59.94), 1280x720@60Hz (720p60), 1280x800@60Hz, 1920x1080@50Hz (1080p50), 1920x1080@59.94Hz (1080p59.94), 1920x1080@60Hz (1080p60)
Audio
Signal Types
Input
Network video over Ethernet via RJ45
Output
Embedded audio on DVI-D or HDMI (through adapter)
Formats
HDMI
8ch PCM
Analog
Stereo 2-channel
Digital-To-Analog Conversion
16-bit 32 kHz, 44.1 kHz and 48 kHz
Latency
720p
25 ms
1080p
25 ms

Note: Scaling can add up to 16 ms of latency.

Note: To calculate an end-to-end latency value, add the given Decoder latency (shown above) to your Encoder's latency (which is provided in the Encoder's Specifications sheet).

Communications
Ethernet
10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
HDMI
HDCP, EDID management
Ports
+12V 2A
One 12 Volt DC power input.
P0 POE
8-wire RJ45 female.
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port. Provides both the network connection and the power to the Encoders and Decoders. See the section Power Requirements on page 3 for more information.
P1
8-wire RJ45 female.
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port.
IR
2-pin terminal Phoenix connector. Provides Infrared (IR) output only (33-60 kHz). Emitter may be necessary (not included).
RS232
3-pin terminal Phoenix connector which provides a serial control interface. Full duplex communication. Available terminal speed settings: 9600-115200 baud rate.
AUDIO
5-pin terminal Phoenix connector which provides user-selectable balanced/unbalanced input. Dedicated audio input.
DVI-D OUTPUT
DVI-D female; HDMI/DVI digital video/audio output. Allows for video and embedded digital audio output.
LEDs and Buttons
FRONT PANEL


RESET button
Recessed pushbutton. Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings.
ID button
Recessed pushbutton. Press to send a notification out on the network to identify the unit (the notification causes a pop-up dialog in N-Able and N-Command).
POWER LED
On solid (green) when operating power is supplied (via local power supply). This activity is also shown by the PWR LED on the rear panel.
STATUS LED
On flashing (green) when there is software activity. This activity is also shown by the STAT LED on the rear panel.
REAR PANEL


PWR LED
Same as POWER LED described above.
DVI LED
On (green) when a DVI outputconnection exists.
STAT LED
Same as STATUS LED described above.
STRM LED
On (green) when the unit is streaming video.
Power Requirements
Power Supply
2.0 Amp @ 12 Volts DC; 100-240 Volts AC power supply; part number NMX-ACC-N9312.
Physical
Mounting Options
Stand alone, surface mount, or wall mount. Mounting wings (sold separately — part number NMX-ACC-N9101) are required for mounting.
Environmental
Temperature
32° to 104°F (0° to 40°C)
Humidity
10% to 90% RH (non-condensing)
Heat Dissipation
Up to ~44 BTU/Hr
Dimensions
Height
1.05 inches (2.67 cm)
Width
7.888 inches (20.04 cm)
Depth
5 inches (12.7 cm)
Weight
1.5 lbs (0.68 kg)
Compliance
FCC, CE, and NTRL

*Mounting wings (part number NMX-ACC-N9101) required for surface and wall mounting. Rack shelf (part number NMX-ACC-N9102) or card cage (part number NMX-ACC-N9206) required for rack mounting. Shelf accommodates two side-by-side N-Series encoders and decoders. Card cage accommodates up to six N-Series encoder and decoder cards (mix and match any series). Mounting accessories sold separately and are compatible with most N-Series devices.



Note: Specifications are subject to change. The most current and complete specifications for this product can always be found at AMX.com: AV for an IT World.


NAME DESCRIPTION PART #
NMX-ACC-N9101 N-Series, Mounting Brackets (FGN9101)
NMX-ACC-N9102 Rack Shelf, 1RU, 2 N-Series Units (FGN9102)
Feedback | Gear Store | Site Map | Terms of Use | Privacy Policy | Warranty